If you wish to add some nodes to your cluster, simply configure the new nodes to find the existing cluster and start them up. Elasticsearch adds the new nodes to the voting configuration if it is appropriate to do so.

During master election or when joining an existing formed cluster, a node sends a join request to the master in order to be officially added to the cluster. You can use the cluster.join.timeout setting to configure how long a node waits after sending a request to join a cluster. Its default value is 30s. See Discovery and cluster formation settings.

When removing master-eligible nodes, it is important not to remove too many all at the same time. For instance, if there are currently seven master-eligible nodes and you wish to reduce this to three, it is not possible simply to stop four of the nodes at once: to do so would leave only three nodes remaining, which is less than half of the voting configuration, which means the cluster cannot take any further actions.

As long as there are at least three master-eligible nodes in the cluster, as a general rule it is best to remove nodes one-at-a-time, allowing enough time for the cluster to automatically adjust the voting configuration and adapt the fault tolerance level to the new set of nodes.

If there are only two master-eligible nodes remaining then neither node can be safely removed since both are required to reliably make progress. You must first inform Elasticsearch that one of the nodes should not be part of the voting configuration, and that the voting power should instead be given to other nodes. You can then take the excluded node offline without preventing the other node from making progress. A node which is added to a voting configuration exclusion list still works normally, but Elasticsearch tries to remove it from the voting configuration so its vote is no longer required. Importantly, Elasticsearch will never automatically move a node on the voting exclusions list back into the voting configuration. Once an excluded node has been successfully auto-reconfigured out of the voting configuration, it is safe to shut it down without affecting the cluster’s master-level availability. A node can be added to the voting configuration exclusion list using the Voting Configuration Exclusions API. For example:

# Add node to voting configuration exclusions list and wait for the system to
# auto-reconfigure the node out of the voting configuration up to the default
# timeout of 30 seconds
POST /_cluster/voting_config_exclusions/node_name

# Add node to voting configuration exclusions list and wait for
# auto-reconfiguration up to one minute
POST /_cluster/voting_config_exclusions/node_name?timeout=1m

The node that should be added to the exclusions list is specified using node filters in place of node_name here. If a call to the voting configuration exclusions API fails, you can safely retry it. Only a successful response guarantees that the node has actually been removed from the voting configuration and will not be reinstated. If it’s the active master that was removed from the voting configuration, then it will abdicate to another master-eligible node that’s still in the voting configuration, if such a node is available.

Although the voting configuration exclusions API is most useful for down-scaling a two-node to a one-node cluster, it is also possible to use it to remove multiple master-eligible nodes all at the same time. Adding multiple nodes to the exclusions list has the system try to auto-reconfigure all of these nodes out of the voting configuration, allowing them to be safely shut down while keeping the cluster available. In the example described above, shrinking a seven-master-node cluster down to only have three master nodes, you could add four nodes to the exclusions list, wait for confirmation, and then shut them down simultaneously.

Voting exclusions are only required when removing at least half of the master-eligible nodes from a cluster in a short time period. They are not required when removing master-ineligible nodes, nor are they required when removing fewer than half of the master-eligible nodes.

Adding an exclusion for a node creates an entry for that node in the voting configuration exclusions list, which has the system automatically try to reconfigure the voting configuration to remove that node and prevents it from returning to the voting configuration once it has removed. The current list of exclusions is stored in the cluster state and can be inspected as follows:

GET /_cluster/state?filter_path=metadata.cluster_coordination.voting_config_exclusions

This list is limited in size by the cluster.max_voting_config_exclusions setting, which defaults to 10. See Discovery and cluster formation settings. Since voting configuration exclusions are persistent and limited in number, they must be cleaned up. Normally an exclusion is added when performing some maintenance on the cluster, and the exclusions should be cleaned up when the maintenance is complete. Clusters should have no voting configuration exclusions in normal operation.

If a node is excluded from the voting configuration because it is to be shut down permanently, its exclusion can be removed after it is shut down and removed from the cluster. Exclusions can also be cleared if they were created in error or were only required temporarily:

# Wait for all the nodes with voting configuration exclusions to be removed from
# the cluster and then remove all the exclusions, allowing any node to return to
# the voting configuration in the future.
DELETE /_cluster/voting_config_exclusions

# Immediately remove all the voting configuration exclusions, allowing any node
# to return to the voting configuration in the future.
DELETE /_cluster/voting_config_exclusions?wait_for_removal=false