int socket(int domain, int type, int protocol);
The domain argument specifies a communication domain; this selects the protocol family which will be used for communication. These families are defined in <sys/socket.h>. The currently understood formats include:
| Name | Purpose | Man page |
| AF_UNIX, AF_LOCAL | Local communication |
unix(7)
|
| AF_INET | IPv4 Internet protocols |
ip(7)
|
| AF_INET6 | IPv6 Internet protocols |
ipv6(7)
|
| AF_IPX | IPX - Novell protocols | |
| AF_NETLINK | Kernel user interface device |
netlink(7)
|
| AF_X25 | ITU-T X.25 / ISO-8208 protocol |
x25(7)
|
| AF_AX25 | Amateur radio AX.25 protocol | |
| AF_ATMPVC | Access to raw ATM PVCs | |
| AF_APPLETALK | AppleTalk |
ddp(7)
|
| AF_PACKET | Low level packet interface |
packet(7)
|
| AF_ALG | Interface to kernel crypto API |
The socket has the indicated type, which specifies the communication semantics. Currently defined types are:
Some socket types may not be implemented by all protocol families.
Since Linux 2.6.27, the type argument serves a second purpose: in addition to specifying a socket type, it may include the bitwise OR of any of the following values, to modify the behavior of socket():
The protocol specifies a particular protocol to be used with the socket. Normally only a single protocol exists to support a particular socket type within a given protocol family, in which case protocol can be specified as 0. However, it is possible that many protocols may exist, in which case a particular protocol must be specified in this manner. The protocol number to use is specific to the ``communication domain'' in which communication is to take place; see protocols(5). See getprotoent(3) on how to map protocol name strings to protocol numbers.
Sockets of type SOCK_STREAM are full-duplex byte streams. They do not preserve record boundaries. A stream socket must be in a connected state before any data may be sent or received on it. A connection to another socket is created with a connect(2) call. Once connected, data may be transferred using read(2) and write(2) calls or some variant of the send(2) and recv(2) calls. When a session has been completed a close(2) may be performed. Out-of-band data may also be transmitted as described in send(2) and received as described in recv(2).
The communications protocols which implement a SOCK_STREAM ensure that data is not lost or duplicated. If a piece of data for which the peer protocol has buffer space cannot be successfully transmitted within a reasonable length of time, then the connection is considered to be dead. When SO_KEEPALIVE is enabled on the socket the protocol checks in a protocol-specific manner if the other end is still alive. A SIGPIPE signal is raised if a process sends or receives on a broken stream; this causes naive processes, which do not handle the signal, to exit. SOCK_SEQPACKET sockets employ the same system calls as SOCK_STREAM sockets. The only difference is that read(2) calls will return only the amount of data requested, and any data remaining in the arriving packet will be discarded. Also all message boundaries in incoming datagrams are preserved.
SOCK_DGRAM and SOCK_RAW sockets allow sending of datagrams to correspondents named in sendto(2) calls. Datagrams are generally received with recvfrom(2), which returns the next datagram along with the address of its sender.
SOCK_PACKET is an obsolete socket type to receive raw packets directly from the device driver. Use packet(7) instead.
An fcntl(2) F_SETOWN operation can be used to specify a process or process group to receive a SIGURG signal when the out-of-band data arrives or SIGPIPE signal when a SOCK_STREAM connection breaks unexpectedly. This operation may also be used to set the process or process group that receives the I/O and asynchronous notification of I/O events via SIGIO. Using F_SETOWN is equivalent to an ioctl(2) call with the FIOSETOWN or SIOCSPGRP argument.
When the network signals an error condition to the protocol module (e.g., using a ICMP message for IP) the pending error flag is set for the socket. The next operation on this socket will return the error code of the pending error. For some protocols it is possible to enable a per-socket error queue to retrieve detailed information about the error; see IP_RECVERR in ip(7).
The operation of sockets is controlled by socket level options. These options are defined in <sys/socket.h>. The functions setsockopt(2) and getsockopt(2) are used to set and get options, respectively.
Other errors may be generated by the underlying protocol modules.
The SOCK_NONBLOCK and SOCK_CLOEXEC flags are Linux-specific.
socket() appeared in 4.2BSD. It is generally portable to/from non-BSD systems supporting clones of the BSD socket layer (including System V variants).
The manifest constants used under 4.x BSD for protocol families are PF_UNIX, PF_INET, and so on, while AF_UNIX, AF_INET, and so on are used for address families. However, already the BSD man page promises: "The protocol family generally is the same as the address family", and subsequent standards use AF_* everywhere.
The AF_ALG protocol type was added in Linux 2.6.38. More information on this interface is provided with the kernel HTML documentation at https://www.kernel.org/doc/htmldocs/crypto-API/User.html.
"An Introductory 4.3BSD Interprocess Communication Tutorial" and "BSD Interprocess Communication Tutorial", reprinted in UNIX Programmer's Supplementary Documents Volume 1.