Version: 2019.1 (switch to 2018.3 or 2017.4)
Tutorial: Scripting Root Motion for "in-place" humanoid animations
1D Blending
Other Versions

Blend Trees

A common task in game animation is to blend between two or more similar motions. Perhaps the best known example is the blending of walking and running animations according to the character’s speed. Another example is a character leaning to the left or right as it turns during a run.

It is important to distinguish between Transitions and Blend Trees. While both are used for creating smooth animation, they are used for different kinds of situations.

  • TransitionsThe blend from one state to another in a state machine, such as transitioning a character from a walk to a jog animation. Transitions define how long the blend between states should take, and the conditions that activate the blend. More info
    See in Glossary
    are used for transitioning smoothly from one Animation State to another over a given amount of time. Transitions are specified as part of an Animation State MachineA graph within an Animator Controller that controls the interaction of Animation States. Each state references an Animation Blend Tree or a single Animation Clip. More info
    See in Glossary
    . A transition from one motion to a completely different motion is usually fine if the transition is quick.

  • Blend Trees are used for allowing multiple animations to be blended smoothly by incorporating parts of them all to varying degrees. The amount that each of the motions contributes to the final effect is controlled using a blending parameter, which is just one of the numeric animation parametersUsed to communicate between scripting and the Animator Controller. Some parameters can be set in scripting and used by the controller, while other parameters are based on Custom Curves in Animation Clips and can be sampled using the scripting API. More info
    See in Glossary
    associated with the Animator ControllerControls animation through Animation Layers with Animation State Machines and Animation Blend Trees, controlled by Animation Parameters. The same Animator Controller can be referenced by multiple models with Animator components. More info
    See in Glossary
    . In order for the blended motion to make sense, the motions that are blended must be of similar nature and timing. Blend Trees are a special type of state in an Animation State MachineThe set of states in an Animator Controller that a character or animated GameObject can be in, along with a set of transitions between those states and a variable to remember the current state. The states available will depend on the type of gameplay, but typical states include things like idling, walking, running and jumping. More info
    See in Glossary
    .

Examples of similar motions could be various walk and run animations. In order for the blend to work well, the movements in the clips must take place at the same points in normalized time. For example, walking and running animations can be aligned so that the moments of contact of foot to the floor take place at the same points in normalized time (e.g. the left foot hits at 0.0 and the right foot at 0.5). Since normalized time is used, it doesn’t matter if the clips are of different length.

Using Blend Trees

To start working with a new Blend Tree, you need to:

  1. Right-click on empty space on the Animator Controller Window.
  2. Select Create State > From New Blend Tree from the context menu that appears.
  3. Double-click on the Blend Tree to enter the Blend Tree Graph.

The Animator WindowThe window where the Animator Controller is visualized and edited. More info
See in Glossary
now shows a graph of the entire Blend Tree while the InspectorA Unity window that displays information about the currently selected GameObject, Asset or Project Settings, alowing you to inspect and edit the values. More info
See in Glossary
shows the currently selected node and its immediate children.

The Animator Window shows a graph of the entire Blend Tree. To the left is a Blend Tree with only the root Blend Node (no child nodes have been added yet). To the right is a Blend Tree with a root Blend Node and three Animation Clips as child nodes.
The Animator Window shows a graph of the entire Blend Tree. To the left is a Blend Tree with only the root Blend Node (no child nodes have been added yet). To the right is a Blend Tree with a root Blend Node and three Animation Clips as child nodes.

To add animation clipsAnimation data that can be used for animated characters or simple animations. It is a simple “unit” piece of motion, such as (one specific instance of) “Idle”, “Walk” or “Run”. More info
See in Glossary
to the blend tree you can select the blend tree, then click the plus icon in the motion field in the inspector.

A Blend Node shown in the inspector before any motions have been added. The plus icon is used to add animation clips or child blend trees.
A Blend Node shown in the inspector before any motions have been added. The plus icon is used to add animation clips or child blend trees.

Alternatively, you can add animation clips or child blend nodesA node in a Blend Tree graph that blends animation clip nodes. More info
See in Glossary
by right-clicking on the blend tree and selecting from the context menu:

The context menu when right-clicking on a blend tree node.
The context menu when right-clicking on a blend tree node.

When the blendtree is set up with Animation clips and input parameters, the inspector window gives a graphical visualization of how the animations are combined as the parameter value changes (as you drag the slider, the arrows from the tree root change their shading to show the dominant animation clip).

A 2D Blendtree set up with five animation clips, being previewed in the inspector
A 2D Blendtree set up with five animation clips, being previewed in the inspector

You can select any of the nodes in the Blend Tree graph to inspect it in the Inspector. If the selected node is an Animation Clip the Inspector for that Animation Clip will be shown. The settings will be read-only if the animation is imported from a model. If the node is a Blend Node, the Inspector for Blend Nodes will be shown.

You can choose either 1D or 2D blending from the Blend Type menu; the differences between the two types are described on their own pages in this section.

Blend Trees and Root Motion

The blending between animations is handled using linear interpolationThe estimation of values that determine the shape of an animation curve between two keys. More info
See in Glossary
(ie, the amount of each animation is an average of the separate animations weighted by the blending parameter). However, you should note that root motion is not interpolated in the same way. See the page about root motionMotion of character’s root node, whether it’s controlled by the animation itself or externally. More info
See in Glossary
for further details about how this might affect your characters.

Did you find this page useful? Please give it a rating:

Tutorial: Scripting Root Motion for "in-place" humanoid animations
1D Blending