Reference   Language | Libraries | Comparison | Changes

MKRWAN

modem.joinOTAA()

Description

Attempts to join to the LoRaWAN network using Over-The-Air-Activation (OTAA)

Syntax

modem.joinOTAA(appEui, appKey)
modem.joinOTAA(appEui, appKey, devEui)

Parameters

  • appEui: 64 bit application identifier, EUI-64 (unique)
  • appKey: 128 bit application key
  • devEui: 64 bit end-device identifier, EUI-64 (unique)

Example

/*
  First Configuration
  This sketch demonstrates the usage of MKR WAN 1300 LoRa module.
  This example code is in the public domain.
*/

#include <MKRWAN.h>

LoRaModem modem;

// Uncomment if using the Murata chip as a module
// LoRaModem modem(Serial1);

String appEui;
String appKey;
String devAddr;
String nwkSKey;
String appSKey;

void setup() {
  // put your setup code here, to run once:
  Serial.begin(115200);
  while (!Serial);
  Serial.println("Welcome to MKRWAN1300 first configuration sketch");
  Serial.println("Register to your favourite LoRa network and we are ready to go!");
  // change this to your regional band (eg. US915, AS923, ...)
  if (!modem.begin(EU868)) {
    Serial.println("Failed to start module");
    while (1) {}
  };
  Serial.print("Your module version is: ");
  Serial.println(modem.version());
  Serial.print("Your device EUI is: ");
  Serial.println(modem.deviceEUI());

  int mode = 0;
  while (mode != 1 && mode != 2) {
    Serial.println("Are you connecting via OTAA (1) or ABP (2)?");
    while (!Serial.available());
    mode = Serial.readStringUntil('\n').toInt();
  }

  int connected;
  if (mode == 1) {
    Serial.println("Enter your APP EUI");
    while (!Serial.available());
    appEui = Serial.readStringUntil('\n');

    Serial.println("Enter your APP KEY");
    while (!Serial.available());
    appKey = Serial.readStringUntil('\n');

    appKey.trim();
    appEui.trim();

    connected = modem.joinOTAA(appEui, appKey);
  } else if (mode == 2) {

    Serial.println("Enter your Device Address");
    while (!Serial.available());
    devAddr = Serial.readStringUntil('\n');

    Serial.println("Enter your NWS KEY");
    while (!Serial.available());
    nwkSKey = Serial.readStringUntil('\n');

    Serial.println("Enter your APP SKEY");
    while (!Serial.available());
    appSKey = Serial.readStringUntil('\n');

    devAddr.trim();
    nwkSKey.trim();
    appSKey.trim();

    connected = modem.joinABP(devAddr, nwkSKey, appSKey);
  }

  if (!connected) {
    Serial.println("Something went wrong; are you indoor? Move near a window and retry");
    while (1) {}
  }

  delay(5000);

  int err;
  modem.setPort(3);
  modem.beginPacket();
  modem.print("HeLoRA world!");
  err = modem.endPacket(true);
  if (err > 0) {
    Serial.println("Message sent correctly!");
  } else {
    Serial.println("Error sending message :(");
  }
}

void loop() {
  while (modem.available()) {
    Serial.write(modem.read());
  }
  modem.poll();
}
[Get Code]
A string containing the firmware version

Returns

1 if successfully joined, 0 otherwise

See also





Reference Home

Corrections, suggestions, and new documentation should be posted to the Forum.

The text of the Arduino reference is licensed under a Creative Commons Attribution-ShareAlike 3.0 License. Code samples in the reference are released into the public domain.