GSM SSL Web Client

This sketch connects an Arduino MKR GSM 1400 board to the Arduino homepage, http://arduino.cc, through the GSM network. It then prints the content of the page through the serial monitor of the Arduino Software (IDE).

Hardware Required

Circuit

Code

First, import the GSM library

#include <MKRGSM.h>

SIM cards may have a PIN number that enables their functionality. Define the PIN for your SIM. If your SIM has no PIN, you can leave it blank :

#define PINNUMBER ""

Define a number of constants that contain information about the GPRS network you're going to connect to. You'll need the Access Point Name (APN), login, and password. To obtain this information, contact your network provider for the most up to date information. This page has some information about various carrier settings, but it may not be current.

#define GPRS_APN       "GPRS_APN"
#define GPRS_LOGIN     "login"
#define GPRS_PASSWORD  "password"

Initialize instances of the classes you're going to use. You're going to need the GSM, GPRS, and GSMClient classes.

GSMSSLClient client;
GPRS gprs;
GSM gsmAccess;

Create some variables to hold the server, path, and port you wish to connect to.

char server[] = "arduino.cc";
char path[] = "/";
int port = 443;

In setup, open a serial connection to the computer. After opening the connection, send a message indicating the sketch has started.

void setup(){
  Serial.begin(9600);
  Serial.println("Starting Arduino web client.");

Create a local variable to track the connection status. You'll use this to keep the sketch from starting until the SIM is connected to the network :

boolean notConnected = true;

Connect to the network by calling gsmAccess.begin(). It takes the SIM card's PIN as an argument. You'll also connect to the GPRS network using gprs.attachGPRS(). This requires the APN, login, and password you declared earlier. By placing this inside a while() loop, you can continually check the status of the connection and wait for them to both become true before proceeding.

When the modem does connect and has attached itself to the GPRS network, gsmAccess() will return GSM_READY. Use this as a flag to set the notConnected variable to true or false. Once connected, the remainder of setup will run.

while(notConnected)
  {
    if(gsmAccess.begin(PINNUMBER)==GSM_READY)
        (gprs.attachGPRS(GPRS_APN, GPRS_LOGIN, GPRS_PASSWORD)==GPRS_READY))
      notConnected = false;
    else
    {
      Serial.println("Not connected");
      delay(1000);
    }
  }

Attempt to connect to the server using client.connect(). connect() requires two arguments, the server and port. Once connected to the server, make a HTTP request by calling client.print(). A typical web request looks like "GET pathname HTTP/1.0". print will send the message, just as a browser would.

if (client.connect(server, port))
  {
    Serial.println("connected");
    client.print("GET ");
    client.print(path);
    client.println(" HTTP/1.0");
    client.println();
  }

If the connection to the server failed, make a note of it in the serial monitor, and close up setup.

else
  {
    Serial.println("connection failed");
  }
}

Inside loop, check to see if there are bytes returned from the server. If so, read them and print them to the serial monitor.

if (client.available())
  {
    char c = client.read();
    Serial.print(c);
  }

If the server disconnects, which it will typically do once it has completed the HTTP request, stop the client locally and close the loop.

if (!client.available() && !client.connected())
  {
    Serial.println();
    Serial.println("disconnecting.");
    client.stop();

    // do nothing forevermore:
    for(;;)
      ;
  }
}

Once your code is uploaded, open the serial monitor. You should see the HTML of http://arduino.cc print out on screen when it is received. It will takes about one minute, so don't worry if you haven't a feedback immediately!

The complete sketch is below.

/*
  Web client

 This sketch connects to a website using SSL through a MKR GSM 1400 board. Specifically,
 this example downloads the URL "http://www.arduino.cc/asciilogo.txt" and
 prints it to the Serial monitor.

 Circuit:
 * MKR GSM 1400 board
 * Antenna
 * SIM card with a data plan

 created 8 Mar 2012
 by Tom Igoe
*/


// libraries
#include <MKRGSM.h>

#include "arduino_secrets.h"
// Please enter your sensitive data in the Secret tab or arduino_secrets.h
// PIN Number
const char PINNUMBER[]     = SECRET_PINNUMBER;
// APN data
const char GPRS_APN[]      = SECRET_GPRS_APN;
const char GPRS_LOGIN[]    = SECRET_GPRS_LOGIN;
const char GPRS_PASSWORD[] = SECRET_GPRS_PASSWORD;

// initialize the library instance
GSMSSLClient client;
GPRS gprs;
GSM gsmAccess;

// URL, path and port (for example: arduino.cc)
char server[] = "arduino.cc";
char path[] = "/asciilogo.txt";
int port = 443; // port 443 is the default for HTTPS

void setup() {
  // initialize serial communications and wait for port to open:
  Serial.begin(9600);
  while (!Serial) {
    ; // wait for serial port to connect. Needed for native USB port only
  }

  Serial.println("Starting Arduino web client.");
  // connection state
  bool connected = false;

  // After starting the modem with GSM.begin()
  // attach the shield to the GPRS network with the APN, login and password
  while (!connected) {
    if ((gsmAccess.begin(PINNUMBER) == GSM_READY) &&
        (gprs.attachGPRS(GPRS_APN, GPRS_LOGIN, GPRS_PASSWORD) == GPRS_READY)) {
      connected = true;
    } else {
      Serial.println("Not connected");
      delay(1000);
    }
  }

  Serial.println("connecting...");

  // if you get a connection, report back via serial:
  if (client.connect(server, port)) {
    Serial.println("connected");
    // Make a HTTP request:
    client.print("GET ");
    client.print(path);
    client.println(" HTTP/1.1");
    client.print("Host: ");
    client.println(server);
    client.println("Connection: close");
    client.println();
  } else {
    // if you didn't get a connection to the server:
    Serial.println("connection failed");
  }
}

void loop() {
  // if there are incoming bytes available
  // from the server, read them and print them:
  if (client.available()) {
    char c = client.read();
    Serial.print(c);
  }

  // if the server's disconnected, stop the client:
  if (!client.available() && !client.connected()) {
    Serial.println();
    Serial.println("disconnecting.");
    client.stop();

    // do nothing forevermore:
    for (;;)
      ;
  }
}

See Also




Last revision 2017/11/29 by AG