First Configuration
This example for a MKRFox1200 device allows you to setup the SigFox's backend for your board.
Hardware Required
- MKRFox1200 board
Circuit
There is no circuit for this example.
image developed using Fritzing. For more circuit examples, see the Fritzing project page
Code
In setup() the Serial is initialized. This will allow you to insert your first SigFox message and to get the informations you need to configure the SigFox's backend. Since the MKRFox1200 doesn't have an autoreset function associated to the Serial monitor opening, a Serial while is present. We also check that the SigFox module is present and can be used.
Serial.begin(9600);
while(!Serial) {};
if (!SigFox.begin()) {
Serial.println("Shield error or not present!");
return;
}
After this, we can read our ID and PAC that you have to use to register your board.
String ID = SigFox.ID();
String PAC = SigFox.PAC();
// Display module informations
Serial.println("MKRFox1200 Sigfox first configuration");
Serial.println("SigFox FW version " + version);
Serial.println("ID = " + ID);
Serial.println("PAC = " + PAC);
Serial.println("");
Serial.print("Module temperature: ");
Serial.println(SigFox.temperatureInternal());
Serial.println("Register your board on https://backend.sigfox.com/activate with provided ID and PAC");
delay(100);
// Send the module to the deepest sleep
SigFox.end();
Register your board
To register you board you have to navigate to the SigFox backend. This is an one time registration process, needed once for every MKR FOX 1200 you own.
Select the country where the user is residing or using it right now
After that, enter your ID and PAC number which was shown on the serial monitor after uploading the sketch the FIRST CONFIG.
Now you can check the incoming and outgoing messages from the sigfox back end.
Input your credentials to get to the Sigfox portal home page.
Now we have to make sure that our Downlink mode is set to Direct and not Callback
Click on the Device type and then click on the Keep Alive and click Edit
So, put Downlink mode to Direct to receive messages back and forth
Now you can go back to the main Sigfox portal page and click on the Device on Top left, then click on the ID as shown in the image below
Select the messages item on the left menu bar.
In this page you can see the messages. If it is sent properly, then you can see the green call back otherwise, you can see callback as a red arrow
When the configuration for callback is done properly, you can send your first message! If your message is correctly delivered you will get a response from the server similar to:
Otherwise an error message will be printed on the serial monitor
In loop() we have no instructions since we don't need to do something more.
Complete code
SigFox First Configuration
This sketch demonstrates the usage of MKRFox1200 SigFox module.
Since the board is designed with low power in mind, it depends directly on ArduinoLowPower library
This example code is in the public domain.
*/
#include <SigFox.h>
#include <ArduinoLowPower.h>
void setup() {
Serial.begin(9600);
while (!Serial) {};
// Uncomment this line and comment begin() if you are working with a custom board
//if (!SigFox.begin(SPI1, 30, 31, 33, 28, LED_BUILTIN)) {
if (!SigFox.begin()) {
Serial.println("Shield error or not present!");
return;
}
// Enable debug led and disable automatic deep sleep
// Comment this line when shipping your project :)
SigFox.debug();
String version = SigFox.SigVersion();
String ID = SigFox.ID();
String PAC = SigFox.PAC();
// Display module informations
Serial.println("MKRFox1200 Sigfox first configuration");
Serial.println("SigFox FW version " + version);
Serial.println("ID = " + ID);
Serial.println("PAC = " + PAC);
Serial.println("");
Serial.print("Module temperature: ");
Serial.println(SigFox.internalTemperature());
Serial.println("Register your board on https://backend.sigfox.com/activate with provided ID and PAC");
delay(100);
// Send the module to the deepest sleep
SigFox.end();
Serial.println("Type the message to be sent");
while (!Serial.available());
String message;
while (Serial.available()) {
message += (char)Serial.read();
}
// Every SigFox packet cannot exceed 12 bytes
// If the string is longer, only the first 12 bytes will be sent
if (message.length() > 12) {
Serial.println("Message too long, only first 12 bytes will be sent");
}
Serial.println("Sending " + message);
// Remove EOL
message.trim();
// Example of message that can be sent
// sendString(message);
Serial.println("Getting the response will take up to 50 seconds");
Serial.println("The LED will blink while the operation is ongoing");
// Example of send and read response
sendStringAndGetResponse(message);
}
void loop()
{
}
void sendString(String str) {
// Start the module
SigFox.begin();
// Wait at least 30mS after first configuration (100mS before)
delay(100);
// Clears all pending interrupts
SigFox.status();
delay(1);
SigFox.beginPacket();
SigFox.print(str);
int ret = SigFox.endPacket(); // send buffer to SIGFOX network
if (ret > 0) {
Serial.println("No transmission");
} else {
Serial.println("Transmission ok");
}
Serial.println(SigFox.status(SIGFOX));
Serial.println(SigFox.status(ATMEL));
SigFox.end();
}
void sendStringAndGetResponse(String str) {
// Start the module
SigFox.begin();
// Wait at least 30mS after first configuration (100mS before)
delay(100);
// Clears all pending interrupts
SigFox.status();
delay(1);
SigFox.beginPacket();
SigFox.print(str);
int ret = SigFox.endPacket(true); // send buffer to SIGFOX network and wait for a response
if (ret > 0) {
Serial.println("No transmission");
} else {
Serial.println("Transmission ok");
}
Serial.println(SigFox.status(SIGFOX));
Serial.println(SigFox.status(ATMEL));
if (SigFox.parsePacket()) {
Serial.println("Response from server:");
while (SigFox.available()) {
Serial.print("0x");
Serial.println(SigFox.read(), HEX);
}
} else {
Serial.println("Could not get any response from the server");
Serial.println("Check the SigFox coverage in your area");
Serial.println("If you are indoor, check the 20dB coverage or move near a window");
}
Serial.println();
SigFox.end();
}
See Also
Event Trigger
Last revision 2017/04/26 by AR
