WiFi101 OTA
This example shows how to use
Hardware Required
- MKR1000 board
- MKR SD Protoshield
- SD card
Circuit
image developed using Fritzing. For more circuit examples, see the Fritzing project page
The MKR SD protoshield is intended to be place in top or under the MKR1000 board.
Code
First time you upload this code, you have to do it by means of the USB cable. After the first upload you will see your board listed under the Tools->port menu in the network's port sub menu.
/*
This example connects to an WPA encrypted WiFi network.
Then it prints the MAC address of the Wifi shield,
the IP address obtained, and other network details.
It then polls for sketch updates over WiFi, sketches
can be updated by selecting a network port from within
the Arduino IDE: Tools -> Port -> Network Ports ...
Circuit:
* WiFi shield attached
* SD shield attached
created 13 July 2010
by dlf (Metodo2 srl)
modified 31 May 2012
by Tom Igoe
modified 16 January 2017
by Sandeep Mistry
*/
#include <SPI.h>
#include <SD.h>
#include <WiFi101.h>
#include <WiFi101OTA.h>
#include <SDU.h>
char ssid[] = "yourNetwork"; // your network SSID (name)
char pass[] = "secretPassword"; // your network password
int status = WL_IDLE_STATUS;
void setup() {
//Initialize serial:
Serial.begin(9600);
// setup SD card
Serial.print("Initializing SD card...");
if (!SD.begin(SDCARD_SS_PIN)) {
Serial.println("initialization failed!");
// don't continue:
while (true);
}
Serial.println("initialization done.");
// check for the presence of the shield:
if (WiFi.status() == WL_NO_SHIELD) {
Serial.println("WiFi shield not present");
// don't continue:
while (true);
}
// attempt to connect to Wifi network:
while ( status != WL_CONNECTED) {
Serial.print("Attempting to connect to SSID: ");
Serial.println(ssid);
// Connect to WPA/WPA2 network. Change this line if using open or WEP network:
status = WiFi.begin(ssid, pass);
}
// start the WiFi OTA library with SD based storage
WiFiOTA.begin("Arduino", "password", SDStorage);
// you're connected now, so print out the status:
printWifiStatus();
}
void loop() {
// check for WiFi OTA updates
WiFiOTA.poll();
// add your normal loop code below ...
}
void printWifiStatus() {
// print the SSID of the network you're attached to:
Serial.print("SSID: ");
Serial.println(WiFi.SSID());
// print your WiFi shield's IP address:
IPAddress ip = WiFi.localIP();
Serial.print("IP Address: ");
Serial.println(ip);
// print the received signal strength:
long rssi = WiFi.RSSI();
Serial.print("signal strength (RSSI):");
Serial.print(rssi);
Serial.println(" dBm");
}
This example connects to an WPA encrypted WiFi network.
Then it prints the MAC address of the Wifi shield,
the IP address obtained, and other network details.
It then polls for sketch updates over WiFi, sketches
can be updated by selecting a network port from within
the Arduino IDE: Tools -> Port -> Network Ports ...
Circuit:
* WiFi shield attached
* SD shield attached
created 13 July 2010
by dlf (Metodo2 srl)
modified 31 May 2012
by Tom Igoe
modified 16 January 2017
by Sandeep Mistry
*/
#include <SPI.h>
#include <SD.h>
#include <WiFi101.h>
#include <WiFi101OTA.h>
#include <SDU.h>
char ssid[] = "yourNetwork"; // your network SSID (name)
char pass[] = "secretPassword"; // your network password
int status = WL_IDLE_STATUS;
void setup() {
//Initialize serial:
Serial.begin(9600);
// setup SD card
Serial.print("Initializing SD card...");
if (!SD.begin(SDCARD_SS_PIN)) {
Serial.println("initialization failed!");
// don't continue:
while (true);
}
Serial.println("initialization done.");
// check for the presence of the shield:
if (WiFi.status() == WL_NO_SHIELD) {
Serial.println("WiFi shield not present");
// don't continue:
while (true);
}
// attempt to connect to Wifi network:
while ( status != WL_CONNECTED) {
Serial.print("Attempting to connect to SSID: ");
Serial.println(ssid);
// Connect to WPA/WPA2 network. Change this line if using open or WEP network:
status = WiFi.begin(ssid, pass);
}
// start the WiFi OTA library with SD based storage
WiFiOTA.begin("Arduino", "password", SDStorage);
// you're connected now, so print out the status:
printWifiStatus();
}
void loop() {
// check for WiFi OTA updates
WiFiOTA.poll();
// add your normal loop code below ...
}
void printWifiStatus() {
// print the SSID of the network you're attached to:
Serial.print("SSID: ");
Serial.println(WiFi.SSID());
// print your WiFi shield's IP address:
IPAddress ip = WiFi.localIP();
Serial.print("IP Address: ");
Serial.println(ip);
// print the received signal strength:
long rssi = WiFi.RSSI();
Serial.print("signal strength (RSSI):");
Serial.print(rssi);
Serial.println(" dBm");
}
See Also
WiFi101_OTA
Last revision 2017/03/24 by AG
