Tutorials > Examples from Libraries > VidorGraphics > VidorQrRecognition

QR Code Recognition

This example shows the flexibility and power of the FPGA architecture. A QR code recognition set of APIs is included in the VidorGraphics library and the corresponding IP is in the bitstream that is loaded in the FPGA together with the sketch for the SAMD core. The example highlights on video the QR code markers and prints on the serial monitor the coordinates of the markers found.

Hardware Required

Circuit

There is no circuit for this example.

Code

Include the VidorCamera library, which is part of VidorGraphics.
#include "VidorGraphics.h"
#include "VidorCamera.h"

You have a number of functions available to manage the recognition of a QR Code. VidorQR is part of the VidorCam library; the functions are accessible with cam.qrrec.

  • void begin() - start recognition algorithm
  • void end() - stops recognition
  • void setMode(uint8_t mode); - change video mode
  • void setThr(uint8_t thr); - set recognition thresold
  • int readQRCode(void); - perform qr code recognition
  • sQrDet qr; - structure containing detected points


#include "VidorGraphics.h"
#include "VidorCamera.h"

VidorCamera vcam;

#define MAXDIM 10

static uint16_t x[QR_PT_DET_NUM], y[QR_PT_DET_NUM];

struct qrPtn {
  uint16_t x[QR_PT_DET_NUM];
  uint16_t y[QR_PT_DET_NUM];
};

static qrPtn qrBufferPtn[MAXDIM];

uint16_t count = 0, last;

void setup() {
  Serial.begin(9600);

  // wait for the serial monitor to open,
  // if you are powering the board from a USB charger remove the next line
  while (!Serial);

  if (!FPGA.begin()) {
    Serial.println("Initialization failed!");
    while (1) {}
  }
  /**
    begin() enable the I2C communication and initialize the display for the camera
  */
  if (!vcam.begin()) {
    Serial.println("Camera begin failed");
    while (1) {}
  }
  /**
      qrrec.begin(); enable the QR code recognition
  */
  vcam.qrrec.begin();
  delay(4000);
  Serial.println("Power ON");
}

void loop()  {
  /**
     qrrec.readQRCode(); get, if available, the coordinates of the QR code in the screen
  */
  vcam.qrrec.readQRCode();
  for (int i = 0; i < QR_PT_DET_NUM; i++) {
    if (vcam.qrrec.qr.pt[i].valid) {
      x[i] = (vcam.qrrec.qr.pt[i].xs + vcam.qrrec.qr.pt[i].xe) / 2;
      y[i] = (vcam.qrrec.qr.pt[i].ys + vcam.qrrec.qr.pt[i].ye) / 2;
      vcam.vgfx.Cross(x[i], y[i], 65535);

    }
  }

  last = count % MAXDIM;
  for (int i = 0; i < QR_PT_DET_NUM; i++) {
    vcam.vgfx.Cross(qrBufferPtn[last].x[i], qrBufferPtn[last].y[i], 0, 0);
    qrBufferPtn[last].x[i] = x[i];
    qrBufferPtn[last].y[i] = y[i];
  }
  count++;
}
[Get Code]

See Also

  • Enable Camera - Enables the video stream from a camera to an HDMI monitor
  • Draw Logo - Draw the Arduino Logo on an HDMI monitor
  • Encoder – Manage easily quadrature encoders and never lose an impulse


For more details on the Arduino MKR Vidor 4000, see the product page.

Last revision 2018/07/22 by SM