Swarm and container networks

You are viewing docs for legacy standalone Swarm. These topics describe standalone Docker Swarm. In Docker 1.12 and higher, Swarm mode is integrated with Docker Engine. Most users should use integrated Swarm mode — a good place to start is Getting started with swarm mode, Swarm mode CLI commands, and the Get started with Docker walkthrough). Standalone Docker Swarm is not integrated into the Docker Engine API and CLI commands.

Estimated reading time: 3 minutes

Docker Swarm is fully compatible with Docker’s networking features. This includes the multi-host networking feature which allows creation of custom container networks that span multiple Docker hosts.

Before using Swarm with a custom network, read through the conceptual information in Docker container networking. You should also have walked through the Get started with multi-host networking example.

Create a custom network in a Swarm cluster

Multi-host networks require a key-value store. The key-value store holds information about the network state which includes discovery, networks, endpoints, IP addresses, and more. Through the Docker’s libkv project, Docker supports Consul, Etcd, and ZooKeeper key-value store backends. For details about the supported backends, refer to the libkv project.

To create a custom network, you must choose a key-value store backend and implement it on your network. Then, you configure the Docker Engine daemon to use this store. Two required parameters, --cluster-store and --cluster-advertise, refer to your key-value store server.

Once you’ve configured and restarted the daemon on each Swarm node, you are ready to create a network.

List networks

This example assumes there are two nodes node-0 and node-1 in the cluster. From a Swarm node, list the networks:

$ docker network ls
NETWORK ID          NAME                   DRIVER
3dd50db9706d        node-0/host            host
09138343e80e        node-0/bridge          bridge
8834dbd552e5        node-0/none            null
45782acfe427        node-1/host            host
8926accb25fd        node-1/bridge          bridge
6382abccd23d        node-1/none            null

As you can see, each network name is prefixed by the node name.

Create a network

By default, Swarm is using the overlay network driver, a global-scope network driver. A global-scope network driver creates a network across an entire Swarm cluster. When you create an overlay network under Swarm, you can omit the -d option:

$ docker network create swarm_network
42131321acab3233ba342443Ba4312
$ docker network ls
NETWORK ID          NAME                   DRIVER
3dd50db9706d        node-0/host            host
09138343e80e        node-0/bridge          bridge
8834dbd552e5        node-0/none            null
42131321acab        node-0/swarm_network   overlay
45782acfe427        node-1/host            host
8926accb25fd        node-1/bridge          bridge
6382abccd23d        node-1/none            null
42131321acab        node-1/swarm_network   overlay

As you can see here, both the node-0/swarm_network and the node-1/swarm_network have the same ID. This is because when you create a network on the cluster, it is accessible from all the nodes.

To create a local scope network (for example with the bridge network driver) you should use <node>/<name> otherwise your network is created on a random node.

$ docker network create node-0/bridge2 -b bridge
921817fefea521673217123abab223
$ docker network create node-1/bridge2 -b bridge
5262bbfe5616fef6627771289aacc2
$ docker network ls
NETWORK ID          NAME                   DRIVER
3dd50db9706d        node-0/host            host
09138343e80e        node-0/bridge          bridge
8834dbd552e5        node-0/none            null
42131321acab        node-0/swarm_network   overlay
921817fefea5        node-0/bridge2         bridge
45782acfe427        node-1/host            host
8926accb25fd        node-1/bridge          bridge
6382abccd23d        node-1/none            null
42131321acab        node-1/swarm_network   overlay
5262bbfe5616        node-1/bridge2         bridge

--opt encrypted is a feature only available in Docker Swarm mode. It’s not supported in Swarm standalone. Network encryption requires key management, which is outside the scope of Swarm.

Remove a network

To remove a network you can use its ID or its name. If two different networks have the same name, include the <node> value:

$ docker network rm swarm_network
42131321acab3233ba342443Ba4312
$ docker network rm node-0/bridge2
921817fefea521673217123abab223
$ docker network ls
NETWORK ID          NAME                   DRIVER
3dd50db9706d        node-0/host            host
09138343e80e        node-0/bridge          bridge
8834dbd552e5        node-0/none            null
45782acfe427        node-1/host            host
8926accb25fd        node-1/bridge          bridge
6382abccd23d        node-1/none            null
5262bbfe5616        node-1/bridge2         bridge

The swarm_network was removed from every node. The bridge2 was removed only from node-0.

Docker Swarm documentation index

Rate this page:

 
4
 
3